Kold-Draft Error 60: Water Fill Timeout
Severity
medium
Difficulty
Easy
Time
15-30 min
Pro Cost
$100-$300
| Error Code | Error 60 |
|---|---|
| Meaning | Water Fill Timeout |
| Quick Fix | Verify water supply valve is fully open |
| Tools Needed | Water pressure gauge, Wrench for filter housing |
| Affected Models | GT360, GT560, GB561, GBX564, GTX360, GBX560 |
Kold-Draft Error Error 60 indicates water fill timeout. Error 60 indicates the water fill cycle exceeded its time limit (3-5 minutes). The machine cannot fill with water fast enough. This is often the easiest Kold-Draft error to diagnose.
What Causes Kold-Draft Error Error 60?
Possible Causes
- 1 Water supply valve turned off
- 2 Clogged water filter (especially common with Houston hard water)
- 3 Water inlet solenoid valve stuck closed or not receiving signal
- 4 Low water pressure (below 20 PSI dynamic minimum)
Affected Models
Houston Climate Factor
Houston's sediment-heavy water clogs Kold-Draft water filters fast. Replace filters every 3 months and consider a sediment pre-filter for extra protection.
Tools & Parts You'll Need
Tools Required
- Water pressure gauge
- Wrench for filter housing
Parts That May Be Needed
- Water filter $30-$60
- Water inlet solenoid valve $45-$85
How to Fix Kold-Draft Error Error 60
Follow these steps to troubleshoot and potentially resolve the Error 60 error on your Kold-Draft ice machine.
Before You Start
- 1. Disconnect power — unplug your Kold-Draft ice machine
- 2. Turn off water supply — prevent leaks during repair
- 3. Check warranty — DIY repairs may void coverage
Step 1
Verify water supply valve is fully open
Step 2
Replace water filter if overdue
Step 3
Check for kinked supply lines
Step 4
Test water pressure (20-100 PSI required, 30-50 PSI recommended)
Did these steps resolve the error?
Great news!
To prevent this from happening again, check the prevention tips below.
View Prevention TipsLooks like you need a pro
This Error 60 error on your Kold-Draft may require professional diagnosis. Houston technicians can typically resolve this for $100-$300.
How to Prevent Kold-Draft Error Error 60
Replace water filter every 3 months with Houston hard water
Install a pressure regulator if building pressure exceeds 80 PSI
Check water supply after any building plumbing work
When to Call a Kold-Draft Professional
If water supply and filter are good, the inlet solenoid valve likely needs replacement.
Frequently Asked Questions
What does Kold-Draft error Error 60 mean?
Error 60 indicates the water fill cycle exceeded its time limit (3-5 minutes). The machine cannot fill with water fast enough. This is often the easiest Kold-Draft error to diagnose.
How do I fix Kold-Draft Error 60 error?
To fix Kold-Draft Error 60: Verify water supply valve is fully open. Replace water filter if overdue. Check for kinked supply lines. If water supply and filter are good, the inlet solenoid valve likely needs replacement.
Is Kold-Draft Error 60 serious?
Kold-Draft Error 60 is rated as medium severity. Some DIY troubleshooting may help, but professional service may be needed.
How much does it cost to fix Kold-Draft Error 60?
Typical repair cost for Kold-Draft Error 60 is $100-$300. This includes diagnosis, parts, and labor. Professional ice machine cleaning in Houston starts at $199.
What tools do I need to fix Kold-Draft Error 60?
You'll need: Water pressure gauge, Wrench for filter housing. Always disconnect power before starting any repairs.
Can I fix Kold-Draft Error 60 myself?
This repair is rated as easy difficulty. Most people can handle this with basic tools. Estimated time: 15-30 min.
Other Kold-Draft Error Codes
View all Kold-Draft codes →Diagnostic Tools
Need Help With Kold-Draft Error Error 60?
Houston Kold-Draft specialists available for same-day service. Get a free quote in minutes.