Kold-Draft Error 10: Evaporator Over-Temperature
Severity
high
Difficulty
Advanced
Time
60-120 min
Pro Cost
$200-$500
| Error Code | Error 10 |
|---|---|
| Meaning | Evaporator Over-Temperature |
| Quick Fix | Power cycle the machine and monitor for recurrence |
| Tools Needed | Multimeter, Temperature probe, Refrigerant gauges |
| Affected Models | GT360, GT560, GB561, GBX564, GTX360, GBX560 |
Kold-Draft Error Error 10 indicates evaporator over-temperature. Error 10 indicates the evaporator temperature probe is reading above 120°F. The machine shuts down to protect components. This typically indicates a probe malfunction, stuck hot gas valve, or control board issue.
What Causes Kold-Draft Error Error 10?
Possible Causes
- 1 Bad evaporator temperature probe or misalignment (the #1 diagnostic issue on Kold-Draft)
- 2 Hot gas solenoid valve stuck open, flooding evaporator with hot refrigerant
- 3 Faulty control board misreading probe signal
Affected Models
Houston Climate Factor
Houston's extreme summer heat can push ambient conditions that stress the refrigerant system. Ensure proper ventilation and monthly condenser cleaning to reduce strain.
Tools & Parts You'll Need
Tools Required
- Multimeter
- Temperature probe
- Refrigerant gauges
Parts That May Be Needed
- Evaporator temperature probe $40-$80
- Hot gas solenoid valve $100-$200
- Control board $800-$2500
How to Fix Kold-Draft Error Error 10
Follow these steps to troubleshoot and potentially resolve the Error 10 error on your Kold-Draft ice machine.
Before You Start
- 1. Disconnect power — unplug your Kold-Draft ice machine
- 2. Turn off water supply — prevent leaks during repair
- 3. Check warranty — DIY repairs may void coverage
Step 1
Power cycle the machine and monitor for recurrence
Did these steps resolve the error?
Great news!
To prevent this from happening again, check the prevention tips below.
View Prevention TipsLooks like you need a pro
This Error 10 error on your Kold-Draft may require professional diagnosis. Houston technicians can typically resolve this for $200-$500.
How to Prevent Kold-Draft Error Error 10
Have probe alignment checked during every service visit
Schedule annual refrigerant system inspection
Install surge protector to protect control board
When to Call a Kold-Draft Professional
Error 10 requires professional diagnosis. The evaporator probe, hot gas valve, and control board all need testing with proper equipment.
Frequently Asked Questions
What does Kold-Draft error Error 10 mean?
Error 10 indicates the evaporator temperature probe is reading above 120°F. The machine shuts down to protect components. This typically indicates a probe malfunction, stuck hot gas valve, or control board issue.
How do I fix Kold-Draft Error 10 error?
To fix Kold-Draft Error 10: Power cycle the machine and monitor for recurrence. Error 10 requires professional diagnosis. The evaporator probe, hot gas valve, and control board all need testing with proper equipment.
Is Kold-Draft Error 10 serious?
Kold-Draft Error 10 is rated as high severity. Professional service is recommended to avoid further damage.
How much does it cost to fix Kold-Draft Error 10?
Typical repair cost for Kold-Draft Error 10 is $200-$500. This includes diagnosis, parts, and labor. Professional ice machine cleaning in Houston starts at $199.
What tools do I need to fix Kold-Draft Error 10?
You'll need: Multimeter, Temperature probe, Refrigerant gauges. Always disconnect power before starting any repairs.
Can I fix Kold-Draft Error 10 myself?
This repair is rated as advanced difficulty. This typically requires professional training and specialized tools. Estimated time: 60-120 min.
Other Kold-Draft Error Codes
View all Kold-Draft codes →Diagnostic Tools
Need Help With Kold-Draft Error Error 10?
Houston Kold-Draft specialists available for same-day service. Get a free quote in minutes.